1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
module cic3_pdm (
input wire clk, // PDM clock
input wire rst, // active-high synchronous reset
input wire pdm_in, // 1-bit PDM data input
input wire [2:0] scale_shift, // Right shift amount (0-7 bits)
input wire [7:0] dc_alpha, // DC removal alpha (0=bypass, 255=strong removal)
output reg signed [15:0] pcm_out, // Decimated PCM output
output reg pcm_valid // Output valid pulse
);
// CIC filter parameters
localparam DECIMATION = 64;
localparam CIC_WIDTH = 17; // 17 bits for safe margin against overflow
// CIC integrator and comb stages
reg signed [CIC_WIDTH-1:0] integrator1, integrator2;
reg signed [CIC_WIDTH-1:0] comb1, comb2;
reg signed [CIC_WIDTH-1:0] comb1_d1, comb2_d1;
// Decimation counter
reg [6:0] decim_count; // 7 bits to match DECIMATION width
// CIC output and scaling
reg signed [CIC_WIDTH-1:0] cic_out;
reg signed [15:0] scaled_out;
reg cic_valid;
// DC removal filter registers
reg signed [19:0] dc_accumulator; // 20-bit to prevent overflow
reg signed [15:0] dc_estimate;
/* verilator lint_off UNUSEDSIGNAL */
// Lower 8 bits of alpha_mult unused - we only need [23:8] for division by 256
reg signed [23:0] alpha_mult; // For alpha multiplication
/* verilator lint_on UNUSEDSIGNAL */
wire signed [CIC_WIDTH-1:0] pdm_signed = pdm_in ? 17'sd1 : -17'sd1;
// CIC Integrator stages (run at PDM rate)
always @(posedge clk) begin
if (rst) begin
integrator1 <= 0;
integrator2 <= 0;
end else begin
integrator1 <= integrator1 + pdm_signed;
integrator2 <= integrator2 + integrator1;
end
end
// Decimation counter and CIC comb stages
always @(posedge clk) begin
if (rst) begin
decim_count <= 0;
comb1 <= 0;
comb2 <= 0;
comb1_d1 <= 0;
comb2_d1 <= 0;
cic_out <= 0;
cic_valid <= 0;
end else begin
cic_valid <= 0;
if (decim_count == DECIMATION - 1) begin
decim_count <= 0;
// Comb stage 1
comb1 <= integrator2 - comb1_d1;
comb1_d1 <= integrator2;
// Comb stage 2
comb2 <= comb1 - comb2_d1;
comb2_d1 <= comb1;
cic_out <= comb2;
cic_valid <= 1;
end else begin
decim_count <= decim_count + 1;
end
end
end
// Output scaling
always @(*) begin
case (scale_shift)
3'd0: scaled_out = cic_out[15:0];
3'd1: scaled_out = cic_out[16:1];
3'd2: scaled_out = {{1{cic_out[16]}}, cic_out[16:2]};
3'd3: scaled_out = {{2{cic_out[16]}}, cic_out[16:3]};
3'd4: scaled_out = {{3{cic_out[16]}}, cic_out[16:4]};
3'd5: scaled_out = {{4{cic_out[16]}}, cic_out[16:5]};
3'd6: scaled_out = {{5{cic_out[16]}}, cic_out[16:6]};
3'd7: scaled_out = {{6{cic_out[16]}}, cic_out[16:7]};
endcase
end
// DC removal filter - runs at decimated rate
always @(posedge clk) begin
if (rst) begin
dc_accumulator <= 20'sd0;
dc_estimate <= 16'sd0;
alpha_mult <= 24'sd0;
pcm_out <= 0;
pcm_valid <= 0;
end else begin
pcm_valid <= 0;
if (cic_valid) begin
// Configurable DC removal using alpha parameter
// If dc_alpha = 0, bypass DC removal
// If dc_alpha = 255, strong DC removal (original /16 behavior)
if (dc_alpha == 8'd0) begin
// Bypass DC removal
pcm_out <= scaled_out;
end else begin
// Calculate alpha * dc_estimate / 256
alpha_mult <= dc_estimate * dc_alpha;
dc_estimate <= dc_accumulator[19:4]; // Current estimate
// Leaky integrator: acc = acc - (alpha/256)*acc + scaled_out
dc_accumulator <= dc_accumulator - {{4{alpha_mult[23]}}, alpha_mult[23:8]} + {{4{scaled_out[15]}}, scaled_out};
// Output with DC removal
pcm_out <= scaled_out - dc_estimate;
end
pcm_valid <= 1;
end
end
end
endmodule
|
